Husqvarna TC 250 2025 Service Schedule

Service work After 1 operating hour Every 15 operating hours Every 45 operating hours Every 90 operating hours Every 24 months
Read out the fault memory using the diagnostics tool.
Check that the electrical equipment is functioning properly.
Check and charge the 12 V battery.
Check that the brake pads of the front brake are secured. (📖 p. 191)
Check that the brake pads of the rear brake are secured. (📖 p. 198)
Check the brake discs. (📖 p. 163)
Check the brake lines for damage and tightness.
Check the brake fluid level for the front brake. (📖 p. 194)
Change the brake fluid for the front brake. (📖 p. 196)
Check the brake fluid level for the rear brake. (📖 p. 201)
Change the brake fluid for the rear brake. (📖 p. 203)
Check/correct the fluid level of the hydraulic clutch. (📖 p. 276)
Change the hydraulic clutch fluid. (📖 p. 276)
Check the free travel on the hand brake lever. (📖 p. 194)
Check the free travel of the brake pedal. (📖 p. 200)
Check the idle speed.
Change the gear oil. (📖 p. 305)
Check all hoses (e.g. fuel, cooling, bleeder, drainage, etc.) and boots for cracking, leaks, and correct routing.
Check the cables for damage and that there are no kinks in the routing.
Check that the clutch cables are undamaged, routed without kinks, and set correctly.
Check the frame. (📖 p. 82)
Check the swingarm. (📖 p. 131)
Check the swingarm bearing for play. (📖 p. 132)
Check the heim joint for play. (📖 p. 96)
Check the shock absorber linkage. (📖 p. 94)
Check the tire condition. (📖 p. 162)
Check the tire pressure. (📖 p. 162)
Check the wheel bearing for play. (📖 p. 163)
Check the hubs.
Check the rim run-out. (📖 p. 164)
Check the spoke tension. (📖 p. 164)
Check the chain, rear sprocket, engine sprocket, and chain guide. (📖 p. 173)
Check the chain tension. (📖 p. 173)
Grease all moving parts (e.g., hand lever, chain, etc.) and check for smooth operation.
Perform the basic setting of the throttle valve with the Husqvarna Motorcycles diagnostics tool. (📖 p. 301)
Change the spark plug and spark plug connector. (📖 p. 310)
Change the fuel filter. (📖 p. 156)
Check the clutch. (📖 p. 278)
Clean the air filter and air filter box. (📖 p. 143)
Change the glass fiber filling of the muffler. (📖 p. 138)
Carry out fork service. (All TC models) (📖 p. 25)
Carry out fork service. (All TX models) (📖 p. 49)
Service the shock absorber. (📖 p. 114)
Check all screws, nuts, and hose clamps for a tight fit.
Change the fuel screen. (📖 p. 158)
Check the fuel pressure. (📖 p. 152)
Check the frost protection and coolant level. (📖 p. 286)
Check the coolant level. (📖 p. 287)
Change the coolant. (📖 p. 290)
Check the steering head bearing play. (📖 p. 73)
Lubricate the steering head bearing. (📖 p. 69)
Check the starter drive. (📖 p. 258)
Check the reed valve housing, diaphragm, and intake manifold. (📖 p. 242)
Perform minor engine service. (Change the piston. Check the cylinder head. Change the O-rings of the manifold and the cylinder head. Check the cylinder and Z-dimension. Clean the exhaust control. Check the exhaust control for function and smooth operation. Program the exhaust control end positions. Check the pressure sensor flange for cracks and damage.)
○ One-time interval    ● Periodic interval

Husqvarna TC 250 Repair manual 2025 Pdf Download